Edge of Dock Leveler with Support Frame – Free-Standing No-Pit Dock Plate SX-EOD-183F

The Edge of Dock Leveler with Support Frame bolts to the approach slab on a fully welded steel frame — no pit, no reliance on dock-face concrete. 6–10 t (13,200–22,000 lb) capacity, spring or hydraulic operation.
View all Edge of Dock Leveler models →

SKU: SX-EOD-183F 分类:
分享您的喜爱

Edge of Dock Leveler with Support Frame – Retrofit Without Pit Work

The Edge of Dock Leveler with Support Frame adds a fully welded structural steel support frame beneath the proven no-pit edge-of-dock deck. Instead of anchoring into the dock face, the free-standing frame is bolted to the approach slab, so the leveler can be fitted to docks with no embedded channels, cracked or low-strength concrete faces, or dock edges that cannot take welding. The frame also raises the whole assembly to match floor levels on raised platforms.

Capacity covers 6–10 t (13,200–22,000 lb) as standard with heavier ratings on request. Choose spring-assisted manual operation or a push-button hydraulic power pack; both versions use the same 1,830 mm (72″) checker plate deck and 400 mm (15.7″) lip as our edge of dock leveler range, and store flush with the dock floor when not in use.

🕑 Quick Specs at a Glance
Capacity: 6–10 t (13,200–22,000 lb), custom to 20 t  |  Deck Width: 1,830 mm (72″) typical  |  Lip: 400 mm (15.7″)  |  Working Range: ±125 mm (±5″) typical  |  Mounting: welded support frame, no pit  |  Model: SX-EOD-183F

Key Features

  • Free-standing welded support frame – carries the full load; no reliance on the dock face concrete
  • Bolt-on installation – anchors into the approach slab; no embedded channels, no wet trades at the dock edge
  • 6–10 t standard capacity (13,200–22,000 lb) – heavier ratings and wider decks manufactured to order
  • Spring or hydraulic operation – manual lever version works power-free; hydraulic version gives push-button lift in ≤ 30 s
  • 1,830 mm (72″) checker plate deck – anti-slip, self-draining, with arch-reinforced 400 mm lip
  • Stores flush with the dock – walk-over surface when idle; dock seals and doors close normally
  • Full frame powder coating – blast-prepared steel with marine-grade top coat for outdoor docks
  • Retrofit friendly – ideal for leased buildings, older docks and temporary platform conversions

Specifications

ParameterValue
Rated capacity6–10 t (13,200–22,000 lb) standard; heavier ratings on request
Deck width1,830 mm (72 in) typical; customised to dock door width
Lip400 mm (15.7 in) long, arch-reinforced chequer + flat plate composite
Working rangeTypically ±125 mm (±5 in); confirmed per dock survey
Support frameFully welded structural steel frame, bolt-down base plates
OperationSpring-assisted manual lever, or hydraulic power pack (push button, ≤ 30 s cycle)
Power (hydraulic version)380V / 220V / 415V / 24V, 0.75 kW; voltage customised to site supply
Surface treatmentBlast cleaning + powder/marine polyurethane coats
Impact protectionLaminated rubber bumpers 300×200×100 mm (11.8×7.9×3.9 in) on steel brackets
Standard supplyDeck assembly, lip assembly, support frame, lever/power pack, bumpers, anchor set
DocumentationInstallation drawing, anchor plan, operation manual, certificate of conformity
Warranty12 months on the complete unit (normal use)

Exact deck size, frame height and lip length are engineered to each dock survey — send drawings for a free fit check. Precise figures are confirmed on the approval drawing, not pre-assumed.

Which Edge of Dock Version Fits Your Dock?

Dock ConditionMountingRecommended Model
Dock face with embedded channel / sound concreteDirect face-mountMechanical Edge of Dock Leveler
Dock face without embedments / weak concrete / leased siteSupport frame, bolt-onThis model (SX-EOD-183F)
Push-button operation requiredHydraulic power packElectric Hydraulic Edge of Dock Leveler

Application Scenarios

🏢 Leased Warehouses
Bolt-on frame leaves the building fabric intact — landlord-friendly retrofit.
🔧 Docks with Damaged Faces
Load goes into the slab through the frame, not the dock edge concrete.
📦 Retrofit & Temporary Platforms
Quick installation with minimal civil work and no production downtime.
❄ Outdoor Yards
Marine-grade coating and laminated bumpers stand up to weather and trailer impacts.

Frequently Asked Questions

Why choose a support frame version instead of direct face-mounting?

When the dock face has no embedded channels, the concrete is cracked or low strength, or the building is leased and cannot be modified, the support frame carries the loading instead of the dock edge. It bolts to the approach slab and keeps the no-pit advantage.

What capacity can the support frame version carry?

Standard configurations cover 6–10 t (13,200–22,000 lb). With an uprated frame, 15 t and 20 t ratings are possible — capacity is confirmed on the approval drawing after the dock survey.

Does the frame need a pit or civil work?

No pit is required. Only anchor bolts into the approach slab are needed; our installation drawing gives the anchor pattern and torque values.

Can I get hydraulic operation on this model?

Yes — the same frame accepts the hydraulic power pack used on our Electric Hydraulic Edge of Dock Leveler, giving push-button lift in under 30 seconds.

Get in Touch

📞
Get a Quote
Send your dock drawings & get pricing within 1 business day

Contact Us →

👥
Custom Sizing
Different capacity, size or finish? We manufacture to spec

Get Custom Quote →

🔍
Browse the Range
Compare all models in this category

View Edge of Dock Leveler →

You may also like: Mechanical Edge of Dock Leveler  |  Electric Hydraulic Edge of Dock Leveler  |  Hydraulic Dock Leveler 10T

评价

目前还没有评价

成为第一个“Edge of Dock Leveler with Support Frame – Free-Standing No-Pit Dock Plate SX-EOD-183F” 的评价者

您的邮箱地址不会被公开。 必填项已用 * 标注

Secure Payments
Tellus gravida ipsum aut facilisis tempus at et aliquam estsem.
Free Shipping
Non pulvinar aenean ultrices lectus vitae imperdiet aeu.
24/7 Support
Nullam iaculis vestibulum arcu id urnain pellentesque quis.
Gifts & Sales
Aliquet ullamcorper leo mi vel sit pretium euismod eget libero.